Re-assemble spit valve that came off
- StefanHaller
- Posts: 63
- Joined: Mar 23, 2018
The screw of the spit valve of my new Getzen trombone came off today. This happened before, last time I could just screw it back in, but this time the whole thing came off and I'm not sure how to put it back together. I think the two single ends of the spring somehow need to go the other side of axle, but I'm not sure how to get them there. I'm afraid I'm also very untalented when it comes to manual work.
Any hints? I would hope I don't have to take it to a technician to repair this...
<ATTACHMENT filename="IMG_2701.jpeg" index="0">[attachment=0]IMG_2701.jpeg</ATTACHMENT>
Any hints? I would hope I don't have to take it to a technician to repair this...
<ATTACHMENT filename="IMG_2701.jpeg" index="0">
- Bonearzt
- Posts: 833
- Joined: Mar 22, 2018
You need some thin hollow metal tubing to use as extensions for the free legs of the spring to comfortably wrap them around and be able to reinsert the screw.
Best bet is to have a tech install a new spring & NOT cut those legs so short!!! Makes it easier to reassemble if it does come off again.
This serves as a good reminder to ALL to check your horn regularly for loose screws!!!!
Eric
Best bet is to have a tech install a new spring & NOT cut those legs so short!!! Makes it easier to reassemble if it does come off again.
This serves as a good reminder to ALL to check your horn regularly for loose screws!!!!
Eric
- JohnL
- Posts: 2529
- Joined: Mar 23, 2018
[quote="StefanHaller"]I'm afraid I'm also very untalented when it comes to manual work.[/quote]
In that case, you might want to just get someone to do it for you. You are correct in thinking that the spring needs to be set; there are special little tools that make doing so easy. Trying to do it yourself with just your bare hands can get very frustrating (not to mention cutting your fingertips when the spring slips - again).
If you do decide to do it yourself, a third (and even fourth) hand can be helpful. Someone to slide the screw in while you manage the spring, water key, and slide.
Here's a video from Edwards on installing a new spring that might be helpful.
<YOUTUBE id="M9htDogU7pc">https://youtu.be/M9htDogU7pc</YOUTUBE>
Unfortunately, your spring has already been trimmed, so working with it won't be as easy.
I tell young players to get in the habit of checking water key and linkage screws whenever they assemble their horn.
In that case, you might want to just get someone to do it for you. You are correct in thinking that the spring needs to be set; there are special little tools that make doing so easy. Trying to do it yourself with just your bare hands can get very frustrating (not to mention cutting your fingertips when the spring slips - again).
If you do decide to do it yourself, a third (and even fourth) hand can be helpful. Someone to slide the screw in while you manage the spring, water key, and slide.
Here's a video from Edwards on installing a new spring that might be helpful.
<YOUTUBE id="M9htDogU7pc">https://youtu.be/M9htDogU7pc</YOUTUBE>
Unfortunately, your spring has already been trimmed, so working with it won't be as easy.
I tell young players to get in the habit of checking water key and linkage screws whenever they assemble their horn.
- StefanHaller
- Posts: 63
- Joined: Mar 23, 2018
Thanks for the advice, I'll take it to the tech then. I guess I'll consider having them install a saturn key instead, while at it.
- elmsandr
- Posts: 1373
- Joined: Mar 23, 2018
Take a couple of coffee strirrers/straws and stick them on the ends of those springs. Use the extension to turn them tighter and move them into position so you can get the screw in. Not hard, but will take patience and a few tries. Don’t put your thumb where it will get poked when the spring pops out of the straw. I actually use the rubber tips of my needle applicator valve oil bottles for this, but some other small tube will work.
Cheers,
Andy
Cheers,
Andy
- Bonearzt
- Posts: 833
- Joined: Mar 22, 2018
[quote="elmsandr"]Take a couple of coffee strirrers/straws and stick them on the ends of those springs. Use the extension to turn them tighter and move them into position so you can get the screw in. Not hard, but will take patience and a few tries. Don’t put your thumb where it will get poked when the spring pops out of the straw. I actually use the rubber tips of my needle applicator valve oil bottles for this, but some other small tube will work.
Cheers,
Andy[/quote]
Nice idea Andy, but with these GetWards springs, they are usually cut too short & the plastic wouldn't be strong enough.
Cheers,
Andy[/quote]
Nice idea Andy, but with these GetWards springs, they are usually cut too short & the plastic wouldn't be strong enough.
- mrdeacon
- Posts: 1225
- Joined: May 08, 2018
If you have a tech close to you just have them do it. It's a pain in the a*$ to reset the spring and isn't worth the effort.
I've reset a couple for high school and middle school kids and always regretted it afterwards haha.
Andy did offer a good solution! I'll have to try that next time.
I've reset a couple for high school and middle school kids and always regretted it afterwards haha.
Andy did offer a good solution! I'll have to try that next time.
- tctb
- Posts: 46
- Joined: Apr 04, 2018
I found the easiest way is to buy a new spring , with long ends putting the valve together is so much easier . The springs are cheap , I usually buy a few as spares.
- timothy42b
- Posts: 1812
- Joined: Mar 27, 2018
I did it myself on my Bach 42B, I think I have a thread here on it somewhere when I replaced the cork. It was tricky but doable.
That Getzen one looks much harder though.
That Getzen one looks much harder though.
- Bonearzt
- Posts: 833
- Joined: Mar 22, 2018
[quote="timothy42b"]I did it myself on my Bach 42B, I think I have a thread here on it somewhere when I replaced the cork. It was tricky but doable.
That Getzen one looks much harder though.[/quote]
The only thing that makes the Getzen/Edwards more difficult is that they are cut too short from the factory to reinstall easily, if at all.
Otherwise same as all other w.key springs.
Eric
That Getzen one looks much harder though.[/quote]
The only thing that makes the Getzen/Edwards more difficult is that they are cut too short from the factory to reinstall easily, if at all.
Otherwise same as all other w.key springs.
Eric
- timothy42b
- Posts: 1812
- Joined: Mar 27, 2018
On the earlier thread, someone described using a pin to hold the parts together before attempting to get the screw threaded.
- Bonearzt
- Posts: 833
- Joined: Mar 22, 2018
[quote="timothy42b"]On the earlier thread, someone described using a pin to hold the parts together before attempting to get the screw threaded.[/quote]
The problem is getting the spring legs in position to be able to get the screw in.
The problem is getting the spring legs in position to be able to get the screw in.
- StefanHaller
- Posts: 63
- Joined: Mar 23, 2018
I took it to the tech this morning, it was a three minute job (as expected, I guess). He put in a new spring.
He had never heard about Saturn keys though...
He had never heard about Saturn keys though...
- Bonearzt
- Posts: 833
- Joined: Mar 22, 2018
[quote="StefanHaller"]I took it to the tech this morning, it was a three minute job (as expected, I guess). He put in a new spring.
He had never heard about Saturn keys though...[/quote]
Saturn w.keys are great!!
http://www.deniswedgwood.com/saturn.htm
Eric
He had never heard about Saturn keys though...[/quote]
Saturn w.keys are great!!
http://www.deniswedgwood.com/saturn.htm
Eric
- timothy42b
- Posts: 1812
- Joined: Mar 27, 2018
[quote="Bonearzt"]<QUOTE author="timothy42b" post_id="87114" time="1560196715" user_id="211">
On the earlier thread, someone described using a pin to hold the parts together before attempting to get the screw threaded.[/quote]
The problem is getting the spring legs in position to be able to get the screw in.
</QUOTE>
I didn't have any trouble with that, but I did struggle a bit getting the screw lined up while holding everything else in place.
On the earlier thread, someone described using a pin to hold the parts together before attempting to get the screw threaded.[/quote]
The problem is getting the spring legs in position to be able to get the screw in.
</QUOTE>
I didn't have any trouble with that, but I did struggle a bit getting the screw lined up while holding everything else in place.
- Kbiggs
- Posts: 1768
- Joined: Mar 24, 2018
[quote="Bonearzt"]<QUOTE author="StefanHaller" post_id="87145" time="1560245654" user_id="74">
I took it to the tech this morning, it was a three minute job (as expected, I guess). He put in a new spring.
He had never heard about Saturn keys though...[/quote]
Saturn w.keys are great!!
http://www.deniswedgwood.com/saturn.htm
Eric
</QUOTE>
I have Saturn water keys on my bass and my tenor. I like that they don’t snag on stuff, and they empty more quickly and quietly than Amado water keys. However...
I’ve noticed they tend to leak. Little water drops thrown right in front of the slide. While it’s fun to watch the violas wonder whether there’s a leak in the ceiling :twisted: , I wonder whether anyone else has this same issue and, if so, what have you done about it?
I took it to the tech this morning, it was a three minute job (as expected, I guess). He put in a new spring.
He had never heard about Saturn keys though...[/quote]
Saturn w.keys are great!!
http://www.deniswedgwood.com/saturn.htm
Eric
</QUOTE>
I have Saturn water keys on my bass and my tenor. I like that they don’t snag on stuff, and they empty more quickly and quietly than Amado water keys. However...
I’ve noticed they tend to leak. Little water drops thrown right in front of the slide. While it’s fun to watch the violas wonder whether there’s a leak in the ceiling :twisted: , I wonder whether anyone else has this same issue and, if so, what have you done about it?
- tbonesullivan
- Posts: 1959
- Joined: Jul 02, 2019
You might want to get some Loc-Tite or even Nail Polish and use that on the threads at the end. It'll help keep it from working its way loose again.