Mute repair
- jrod93
- Posts: 36
- Joined: Jun 21, 2018
I have an old H&B cup mute that is missing the round "red" dot on the front of the mute. I'm wondering if I can cut and glue a replacement piece of wood to plug the hole. Any suggestions for the type of wood or thickness?
- BGuttman
- Posts: 7368
- Joined: Mar 22, 2018
I assume you mean the base of the mute.
ToneColor mutes (a competitor) used to have a 1/4" (6 mm) maple disk as the bottom.
I would guess that any hard wood would be OK. So would epoxy laminate, or even a thin metal plate.
Other materials may give some interesting results even though they won't necessarily sound like a cup mute.
ToneColor mutes (a competitor) used to have a 1/4" (6 mm) maple disk as the bottom.
I would guess that any hard wood would be OK. So would epoxy laminate, or even a thin metal plate.
Other materials may give some interesting results even though they won't necessarily sound like a cup mute.
- timothy42b
- Posts: 1812
- Joined: Mar 27, 2018
I just measured my cup mute bottom at 3.5 inches.
Interesting. Most tape measures have inches on one edge and centimeters on the other. This one has sixteenths marks on one and thirty-seconds on the other. No wonder it was cheap. But I digress. I grabbed a ruler for the metric folk here and it's about 8.6 cm.
Lowes and Home Depot sell flooring samples in a variety of wood types for 25 cents each, sometimes free, and I think they are 4 x 4 inches.
Interesting. Most tape measures have inches on one edge and centimeters on the other. This one has sixteenths marks on one and thirty-seconds on the other. No wonder it was cheap. But I digress. I grabbed a ruler for the metric folk here and it's about 8.6 cm.
Lowes and Home Depot sell flooring samples in a variety of wood types for 25 cents each, sometimes free, and I think they are 4 x 4 inches.
- jrod93
- Posts: 36
- Joined: Jun 21, 2018
Nice ideas guys! Thanks. I'll head to Lowe's in a few. Actually I might have some floor sample in the garage <EMOJI seq="263a" tseq="263a">☺️</EMOJI>
- Doubler
- Posts: 435
- Joined: Jan 07, 2019
In addition to home improvement stores suggested above, craft stores like Hobby Lobby usually have a good selection. You could look on eBay, too.
- jrod93
- Posts: 36
- Joined: Jun 21, 2018
Took DJs advise and repaired it today. Cut to size and pressure fitted. Now I have to paint it.
- Crazy4Tbone86
- Posts: 1654
- Joined: Jan 14, 2020
You might have already painted this "mute," so this might be a "moot" point..... (sorry, but I thought that was slightly clever). Anyway, I was taught years ago that the most effective mutes are sealed and airtight. You might consider sealing that edge with a glue gun or some type of filler.
The "air tight" notion is not something that I necessarily believe. I have had horrible mutes that were air tight and fantastic mutes that leaked profusely. Just throwing it out there as something to consider.
The "air tight" notion is not something that I necessarily believe. I have had horrible mutes that were air tight and fantastic mutes that leaked profusely. Just throwing it out there as something to consider.
- Posaunus
- Posts: 5018
- Joined: Mar 23, 2018
[quote="Crazy4Tbone86"]You might have already painted this "mute," so this might be a "moot" point..... (sorry, but I thought that was slightly clever). Anyway, I was taught years ago that the most effective mutes are sealed and airtight. You might consider sealing that edge with a glue gun or some type of filler.
The "air tight" notion is not something that I necessarily believe. I have had horrible mutes that were air tight and fantastic mutes that leaked profusely. Just throwing it out there as something to consider.[/quote]
[color=#0000FF]Interesting. Some folks make a big point of drilling holes in the bases of their mutes – to make them <B>less</B> airtight! Never done this myself, but ... :idk:
The "air tight" notion is not something that I necessarily believe. I have had horrible mutes that were air tight and fantastic mutes that leaked profusely. Just throwing it out there as something to consider.[/quote]
- jrod93
- Posts: 36
- Joined: Jun 21, 2018
I'm looking at sealing it with glue or caulk. You would think that the side would be like the drilled holes but it's not. The center hole is possible
- Doubler
- Posts: 435
- Joined: Jan 07, 2019
[quote="jrod93"]I'm looking at sealing it with glue or caulk.[/quote]
If it were mine, I'd use Titebond Quick & Thick <LINK_TEXT text="http://www.titebond.com/product/glues/d ... f19351778b">http://www.titebond.com/product/glues/d1b48beb-7d60-4ce7-b57b-6bf19351778b</LINK_TEXT># . Check out the video.
If it were mine, I'd use Titebond Quick & Thick <LINK_TEXT text="http://www.titebond.com/product/glues/d ... f19351778b">http://www.titebond.com/product/glues/d1b48beb-7d60-4ce7-b57b-6bf19351778b</LINK_TEXT># . Check out the video.